blackburn:usingthecrestronpanel

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
blackburn:usingthecrestronpanel [2013/03/11 18:42] – markblackburn:usingthecrestronpanel [2013/03/12 17:15] (current) – mark
Line 4: Line 4:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +<WRAP nopagebreak>
  
  
Line 10: Line 11:
 <WRAP right 400px>{{blackburn:controls.ports.png?390|Input Port Layout}}</WRAP> <WRAP right 400px>{{blackburn:controls.ports.png?390|Input Port Layout}}</WRAP>
  
-The following ports are available for your use, from left to right: +The following ports (from left to right) are available for your use: 
-  * two phone (voice) jacks - only the one on the left (V4038N-08) is activated,+  * two phone (voice) jacks (note: only the one on the left, **V4038N-08** is activated)
   * one network jack (D4038N-75) connected to the Classroom network   * one network jack (D4038N-75) connected to the Classroom network
-    * Call the Information Commons OneStop Support number, 978-0429, prior to your event, to register your equipment for network access,+    * Call the Information Commons OneStop Support number, 978-0429, prior to your event, to register your equipment for network access.
   * one network jack (D4038N-76) connected to the CTSI network   * one network jack (D4038N-76) connected to the CTSI network
-    * Call ..............., prior to your event, to register your equipment for network access, +    * Call ..............., prior to your event, to register your equipment for network access. 
-  * two electrical outlets, +  * two electrical outlets 
-  * two USB ports connected to the Room PC, +  * two USB ports connected to the Room PC 
-  * one 1/8-inch stereo audio input connected to the speaker system and paired with the VGA port, +  * one 1/8-inch stereo audio input connected to the speaker system and paired with the VGA port 
-  * one HDMI input, +  * one HDMI input 
-  * one VGA input.+  * one VGA input
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
 ===== Crestron Panel ===== ===== Crestron Panel =====
  
-The Crestron Panel is used to select which devices (Room PC, laptop, etc) should send audio and video to the desired projector.  The video signal from a single device can be sent to both projectors or from two devices each to a single projector.+The Crestron Panel is used to select which devices (Room PC, laptop, etc.) should send audio and video to the desired projector.  The video signal from a single device can be sent to both projectors or from two devices each to a single projector.
  
-The Crestron Panel, while normally housed in its Wall Cradle, can operate as a roaming, wireless device.  This may be desirable in for following situations: +The Crestron Panel, while normally housed in its Wall Cradle, can operate as a roaming, wireless device.  This may be desirable in the following situations: 
-  * you wish to frequently switch multiple sources during a presentation from the lectern, +  * to frequently switch multiple sources during a presentation from the lectern 
-  * you wish to switch/mute video sources from a desk during a meeting.+  * to switch/mute video sources from a desk during a meeting
  
 The Crestron Panel contains a battery that is sufficient to operate it for a couple of hours. For a day-long event, you will want to use the Crestron Desktop Cradle to extend its operating lifetime.  The Desktop Cradle is stored in the locked equipment cupboard. The Crestron Panel contains a battery that is sufficient to operate it for a couple of hours. For a day-long event, you will want to use the Crestron Desktop Cradle to extend its operating lifetime.  The Desktop Cradle is stored in the locked equipment cupboard.
Line 40: Line 42:
    
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 49: Line 52:
   - Connect and turn on your device (or use the already connected Room PC).   - Connect and turn on your device (or use the already connected Room PC).
   - Select a presentation source:   - Select a presentation source:
-    - ''**Lectern Laptop**'' - if you are using a laptop connected at the lectern, +    - ''**Lectern Laptop**'' - if you are using a laptop connected at the lectern. 
-    - ''**Wall Laptop**'' - if you are using a laptop connected to the wall ports at the Crestron panel,+    - ''**Wall Laptop**'' - if you are using a laptop connected to the wall ports at the Crestron panel.
     - ''**Room PC**'' - if you are using the Room PC.     - ''**Room PC**'' - if you are using the Room PC.
   - Select an output projector, using one of:   - Select an output projector, using one of:
Line 60: Line 63:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 90: Line 94:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 101: Line 106:
   - On the Crestron Panel, select ''**Volume**'' from the right sidebar.   - On the Crestron Panel, select ''**Volume**'' from the right sidebar.
   - Under the ''**Source Volume**'' volume indicator (leftmost set of controls):   - Under the ''**Source Volume**'' volume indicator (leftmost set of controls):
-    - Select and hold the ''**Decrease**'' button to decrease the volume, +    - Select and hold the ''**Decrease**'' button to decrease the volume. 
-    - Select and hold the ''**Increase**'' button to increase the volume,+    - Select and hold the ''**Increase**'' button to increase the volume.
     - Select the ''**Mute**'' button to mute (or unmute) the volume.     - Select the ''**Mute**'' button to mute (or unmute) the volume.
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 117: Line 123:
   - On the Crestron Panel, select ''**Volume**'' from the right sidebar.   - On the Crestron Panel, select ''**Volume**'' from the right sidebar.
   - Under the ''**Lectern Microphone**'' volume indicator (middle set of controls):   - Under the ''**Lectern Microphone**'' volume indicator (middle set of controls):
-    - Select and hold the ''**Decrease**'' button to decrease the volume, +    - Select and hold the ''**Decrease**'' button to decrease the volume. 
-    - Select and hold the ''**Increase**'' button to increase the volume,+    - Select and hold the ''**Increase**'' button to increase the volume.
     - Select the ''**Mute**'' button to mute (or unmute) the volume.     - Select the ''**Mute**'' button to mute (or unmute) the volume.
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 135: Line 142:
   - On the Crestron Panel, select ''**Volume**'' from the right sidebar.   - On the Crestron Panel, select ''**Volume**'' from the right sidebar.
   - Under the ''**Wireless Microphone**'' volume indicator (rightmost set of controls):   - Under the ''**Wireless Microphone**'' volume indicator (rightmost set of controls):
-    - Select and hold the ''**Decrease**'' button to decrease the volume, +    - Select and hold the ''**Decrease**'' button to decrease the volume. 
-    - Select and hold the ''**Increase**'' button to increase the volume,+    - Select and hold the ''**Increase**'' button to increase the volume.
     - Select the ''**Mute**'' button to mute (or unmute) the volume.     - Select the ''**Mute**'' button to mute (or unmute) the volume.
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 153: Line 161:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 165: Line 174:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 174: Line 184:
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 189: Line 200:
  
 __To close the blinds:__ __To close the blinds:__
-  - On the Crestron Panel, select ''**Blinds**'' from the right sidebar,+  - On the Crestron Panel, select ''**Blinds**'' from the right sidebar.
   - Select and hold ''**Raise**'' to raise the blinds from their storage roller.   - Select and hold ''**Raise**'' to raise the blinds from their storage roller.
  
 <WRAP clear></WRAP> <WRAP clear></WRAP>
 +</WRAP><WRAP nopagebreak>
  
  
Line 200: Line 212:
  
 When you are finished presenting, please: When you are finished presenting, please:
-  * At the Crestron Panel, select ''**Turn Off**'' on the lower right side of the display and when prompted confirm your desire to log off.  This will turn off the projectors, roll up the projection screens, and turn up the lights. +  * Turn off the AV System.  At the Crestron Panel, select ''**Turn Off**'' on the lower right side of the display and confirm your desire to log off when prompted.  This will turn off the projectors, roll up the projection screens, and turn up the lights.  **Failure to shut down the system will shorten the life of the projectors and can cause them to overheat and malfunction.  This is especially important if you muted the video before the end of your session.**
-  * **Failure to shut down the system will shorten the life of the projectors and can cause them to overheat and malfunction.  This is especially important if you muted the video before the end of your session.**+
   * Return any Presentation Aids borrowed from the room to their storage locations.   * Return any Presentation Aids borrowed from the room to their storage locations.
 +  * Return the Crestron Panel from its wall socket, if you had removed it, so it can be recharged.  Socket it carefully and ensure the **Charging Indicator** is lit.
  
-  * If you have removed the Crestron Panel from its wall socket, return it so it can be recharged.  Socket it carefully and ensure the **Charging Indicator** is lit.+</WRAP>
  
  • blackburn/usingthecrestronpanel.1363041750.txt.gz
  • Last modified: 2013/03/11 18:42